HomeHomeHomeServicesHome
ServicesServicesServicesServicesServicesDesignServices
About UPPAbout UPPAbout UPPAbout UPPContact UPPAbout UPP

    Compression Software   
    Upgrade Your Browser   
    Download an FTP Program   
    Acrobat Distiller Settings   
    Download Adobe Reader   
    Technical Support   
    Postal Regulations   
    Glossary of Terms   
    Our Preflight Checklist   
    Folding Guide   
    Envelope & Card Sizes   
    Software UPP Accepts   
    How to Copy Fonts
    Proportion Calculator   
    Create PDFs for FREE   
    		 
Many of the more common folds are shown in the following diagrams. Certain folds require "short panels" to allow the finished piece to remain flat. The short panels are identified on the pictures below. The amount of trim for the short panels will depend upon the weight and type of stock used in your project, but a safe measurement is 1/16th of an inch. Use the supplied panel dimensions and dimension calculators to help make sure your project folds correctly. For specific information about your project, contact your Sales or Customer Service Representative.

Quick Jump: Letter Fold  |  Double Parallel Fold/Gate Fold  |  Roll Fold

[4 panel single fold]
Single Fold
(four panels)		 [6 panel accordian fold]
Accordian (or "Z") Fold
(usually six or eight panels)		 [8 panel french fold]
French Fold
(eight panels)

Letter Fold
[6 panel letter fold]
Letter Fold
(six panels)		 11 x 17 (tabloid size)
81/2 x 11 (letter size)
 81/2 x 14 (legal size)

When doing a trifold, divide your paper width by 3 (ie, on an 81/2 x 11 sheet, divide 11 by 3 to get 3.6667). Round that number up to nearest 32nd of an inch (ie, 3.6875). This number will be the size of your two wide panels. To get third third (short) panel, subtract a 16th, or .0625 from the wide panel size (ie, 3.625). The form below will do the work for you, but, since trifolds work with thirds (uneven numbers), the measurements are not always exact (ie, if you add the three numbers together, the sum does not exactly equal the original size). The results are extremely close and are usable.

Sheet width:   Short panel:
    		 Two wide panels:
     		 Exact?
    
Double Parallel Fold/Four-Panel Gate Fold

[8 panel double parallel fold]
Double Parallel Fold
(eight panels)

[8 panel gate fold]
Gate Fold
(eight panels)

When doing a four panel double parallel fold or four panel gate fold, two of the panels are wide and two short. Divide your width by 4 (ie, 17 divided by 4 is 4.25). Add a 32nd, or .03125, to the number to get your wide panel size (ie, 4.28125). Subtract a 16th, or .0625, from the wide panel size to get your short panel size (ie, 4.21875).

Sheet width:   Two wide panels:
     		 Two short panels:
     

Roll Fold

[8 panel barrel (or roll) fold]
Roll Fold
(eight-panels example)

Four panel roll folds have two panels that are the largest size, a short panel, and an even shorter panel. Divide your width by 4 (ie, 17 divided by 4 is 4.25). Add a 16th, or .0625, to the number to get your wide panel size (ie, 4.3125). Subtract 3/32nds, or .09375, from that number to get the short size (ie, 4.21875). To get the final, even shorter size (the shortest size), subtract another 16th, or .0625 (ie, 4.15625). This actually makes the difference between the two large panels and the short panel 3/32s instead of a 16th, but that's only a 32nd of an inch difference.

Sheet width:   Two wide panels:
     		 Short panel:
    		 Shortest:
    
If you need any further help, please feel free to contact any member of our Prepress Department at 919-361-5809, Ext. 133.
 
image map
Home : Help Guides : Folding Guide       // Site Map //